update flash tool
Easyest way...
To go back to previous firmware (ICS V10x_00) with LGFlash Tool there is no need to invent in device properties
or others...
The same methode can be used to do a clean install of the V20A, or other...
Internal memory will be wiped !!!
Be sure that you have the latest drivers installed:
http://www.4shared.com/file/rPpP2btT...S4981MAN3.html
http://www.4shared.com/file/ZSMf2x6n...WHQL_Ver_.html
kdz-update:
http://www.4shared.com/rar/Re4VCOAS/kdz-update.html
install "msxml" (its inside the "kdz-update" folder).
run windows enabler and turn it ON
With battery on the phone and the phone off, press "VOL-" and connect the phone
to the computer while pressing, you'll be in S/W. (If you have issues due the device
being recognized while in S/W Mode, disconnect from PC, take out the battery and
put it back again on the phone, try again "Vol- & connect to PC", wait a few seconds
for Windows to recognize the device).
Run "LGFlashTool" (its inside the "kdz-upload" folder).
select the .dz and the .dll
Official euro_open V20A_00 .dz and .dll:
LGP880AT-00-V20a-262-000-MAR-26-2013+0
http://www.4shared.com/rar/i5muvxCb/...000-MAR-2.html
Official euro_open V10H_00 .dz and .dll:
http://www.4shared.com/rar/LruGBo2Z/V10H_00_dzdll.html
Go to "port settings" and select all 16 ports.
Start the upgrade clicking in the yellow arrow on the top/left of the program window.
Three (3) ports will look like comunicating (in the next image you'll see only two cause I'm not really flashing), but
only one is the right one. Two of them will stay stucked in x% and a third port will go higher. Memorize the one that goes higher cause is that one.
In my case, this time was the nr. 3.
Close the program and re-start it. This time, go to "port settings" and select only the port that you memorized,
start the upgrade and you just need to wait for the phone to reboot.
In case of that port fails, choose one of the other two untill you hit the good one.
If you don't see 3 ports, its something wrong and probably this won't work...
Easy
or others...
The same methode can be used to do a clean install of the V20A, or other...
Internal memory will be wiped !!!
Be sure that you have the latest drivers installed:
http://www.4shared.com/file/rPpP2btT...S4981MAN3.html
http://www.4shared.com/file/ZSMf2x6n...WHQL_Ver_.html
kdz-update:
http://www.4shared.com/rar/Re4VCOAS/kdz-update.html
install "msxml" (its inside the "kdz-update" folder).
run windows enabler and turn it ON
With battery on the phone and the phone off, press "VOL-" and connect the phone
to the computer while pressing, you'll be in S/W. (If you have issues due the device
being recognized while in S/W Mode, disconnect from PC, take out the battery and
put it back again on the phone, try again "Vol- & connect to PC", wait a few seconds
for Windows to recognize the device).
Run "LGFlashTool" (its inside the "kdz-upload" folder).
select the .dz and the .dll
Official euro_open V20A_00 .dz and .dll:
LGP880AT-00-V20a-262-000-MAR-26-2013+0
http://www.4shared.com/rar/i5muvxCb/...000-MAR-2.html
Official euro_open V10H_00 .dz and .dll:
http://www.4shared.com/rar/LruGBo2Z/V10H_00_dzdll.html
Go to "port settings" and select all 16 ports.
Start the upgrade clicking in the yellow arrow on the top/left of the program window.
Three (3) ports will look like comunicating (in the next image you'll see only two cause I'm not really flashing), but
only one is the right one. Two of them will stay stucked in x% and a third port will go higher. Memorize the one that goes higher cause is that one.
In my case, this time was the nr. 3.
Close the program and re-start it. This time, go to "port settings" and select only the port that you memorized,
start the upgrade and you just need to wait for the phone to reboot.
In case of that port fails, choose one of the other two untill you hit the good one.
If you don't see 3 ports, its something wrong and probably this won't work...
Easy
No comments
Post a Comment